Vuze ipfilter2/23/2023 Now you have 3 subnets setup on 3 different ports with DHCP servers and everyone can ping/access one another resources via IP. That completes the setup of the Neighbor1 DHCP server. I use google if I don't know what the fastest ones are in my area. Fill in the DNS servers that work best for you. >next> "Addresses to give out", just leave the default > next > DNS servers. > next> same for the Gateway>next > If it prompts for DHCP relay, just press the up arrow on the screen. You should see one already setup for your local network.Ĭhoose Ether3 > next > DHCP address space 'should' be pre-filled in if you setup the IP address already. This will allow you to easily identify the ports in other screens. )Īlso, in the name, after ether3/4 respectively, add -neighbor1 / - neighbor2 respectively (should look like this ether3-neighbor1). (Make sure master port for eth3 and eth4 is set to 'none'. Next, go to the interface tab, and unslave eth3 and eth4 from eth2.Now on this screen, You want to set your internet info, local network info (192.168.0.1, 255.255.255.0, DHCP server checked, adjust the range to 192.168.0.11-192.168.0.199, and make sure NAT is checked).This is how you can setup 2/3's of your router is no time flat, like your PPOE information on the wan port. (yes, the tab you've been looking for all your life) Then login with Winbox and now you'll see a quickset tab on the left.After you upgrade, reset the router to factory. However, because they're all subnets on the same router, the default routes allow everyone to talk to one another. Now, with this said, your neighbors will need to trust you and they'll need to turn of DHCP on their AP/Routers, and make sure that your feed to them is on a switch port, not a wan port of the AP/Router.Īs you can guess, you don't know how many devices they may have at their house (cell phones, laptops, friends cellphones) and you want to QOS the traffic, they'll need to be on separate subnets. I've drawn a diagram on how I would set this up. I have fiddles so much with the rb750 that i think i should rather reset and start from scratch. ie use ether2 into my adsl modem, and ether3 & 4 to their houses. Do i have to do this, or can i have my ADSL modem do the DHCP and Internet setup etc.ġst prize is i would like to just use the rb750 to be between my network and theirs. Ive been reading up allot and it would seem i need the rb750 to do the PPOE through bridge into my adsl modem. i would like to keep myself completely unrestricted. yes i would want to give them maximum of 2MB internet web traffic bandwidth and maximum local bandwidth. i would be more than happy just blocking all their p2p ( unless allowing them a small amount is easy to do ?) they both have hardwired to their house with a wireless 4 port modem acting as their AP and switch. i want the neighbors to access both my internet and local network (my PC server with movies on they connect via PS3 ) I will update the rb750 now quick thanks. I have added firewall rules but nothing seems to block anything. What i want to do is actually disable all ptp traffic so then i can leave the ether's all unlimited bandwidth and not have them max m line with torrent downloading as they currently do. The problem i have is i am limited to 4MB adsl and if i change their bandwidth to like 2M then when they access my network to watch tv programs and movie via the PS3 it keeps sticking and this i understand is a result of me restricting the entire ether port to only 2MB. i am able to restrict speed by using the normal bandwidth control on the interface screen. i have run hard cable on ether 3, 4 & 5 to wireless AP's at my neighbours houses. The plan is to have my 2 neighbours access internet via my setup. This allows traffic from those ports to access my network. ip gateway 192.168.1.2 ( normal adsl router in dhcp mode )Ģ.)i created a ip address list on the same subnet as my local network.ģ.) i have used ether3,4&5 as the same configuration and made them all use ether2 as the masterport. RB750 ether2 plugged into my original network via network switch. I have a rb750 and have managed to install it on my network and have it working like this : Please excuse my ignorance, but im not very clued up with mikrotik configuration.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |